🔒 Public Trial SandboxRead-only preview — explore all 447 catalog bikes, 38 period catalogs, Rebrickable part matcher & restoration tools freely. Account creation, uploads, ratings & edits are disabled.
Atelier Ciobanu » Technical Info » Technical Glossary

Vintage Bicycle Mechanical Standards & Terminology Glossary (115 of 115)

0–9 & A–Z Jump Bar:

1020

General & Standards

A high-tensile (Hi-Ten) carbon steel used on many bikes, including lower end 'bike boom' bicycles.

4130

General & Standards

4130 is the common generic Cr-Mo used in bicycle frames, pedal spindles and other high strength applications.4130 Cro-Mo steel is stronger than Hi-Tensile (plain carbon steel) but weaker thus heavier than specialized Cr-Mo tube sets such as Reynolds 501 or Columbus SL.41xx is the SAE designation for chromium-molybdenum steels. XX shows the carbon content, 4130 has 0.3%. Chromium content is 1% so rust is only somewhat inhibited.

531

General & Standards

A manganese/molybdenum steel alloy made by Reynolds. They were the undisputed leader in frame materials through the 1960s. "Five-three-one" was used on many high-grade bicycles up through the early '80s and beyond. 531 came in several variations including 531c and 531p, and also found use in race cars and fighter jets.

600

General & Standards

Shimano's second-from-the-top (below Dura Ace) groupset for most of the '80s and '90s. This groupset eventually turned into 600 Ultegra, then Ultegra.

753

General & Standards

Cold drawn, seamless butted manganese-molybdenum tubing most often used for racing frames. It is the same material as 531, but the way it is heat treated gives it different properties. Light and thin-walled, it requires lower temperature silver brazing (vs. brass or bronze). Probably the most well known 753 frame would be the Raleigh Team Pros. Dates from mid to late '70s into the '90s and beyond. Due to 753's delicate characteristics, Reynolds sold the tubesets only to certified framebuilders.

Accushift

General & Standards

SunTour's indexed shifting system, nearly all 6 and 7-speed. Introduced in 1986, but was rushed to production. Suntour could not enforce the quality cabling and staff training required and this caused additional loss of market share to Shimano. Accushift 6-speed shifters pull about the same cable per click as Shimano 7-speed. Accushift clusters had uneven spacing, wider for the smaller cogs. The guide pulley does not have any side play - the derailleur overshifts then returns the pulley to a precise location.

Adapter Claw

General & Standards

The claw-shaped metal adapter for attaching a rear derailleur to a frame that does not have a built-in derailleur hanger. Usually stamped from a single piece of metal and threaded for the derailleur to be attached to. It is secured to the dropout by a small bolt with a special-shaped nut that fits in the back of the dropout's axle slot, and also by the rear axle nut or quick release skewer. Bicycles requiring these adapters are usually a sign of a lower grade frame, or possibly but less likely, a very old one before built in derailleur hangers become common.

Asymmetric Wheel Truing

General & Standards

Process of truing the rear wheel of a bicycle where the spokes on the freewheel side of the rim are shorter and under different tension that the spokes of the opposite side of the rim. Truing in this fashion is done to adjust for the width of the freewheel, to keep the rim exactly on centerline of the axle.

BCD

General & Standards

Bolt Circle Diameter; a measurement of cranksets and chainrings (see also > Chainring).

BCD (Bolt Circle Diameter)

Drivetrain

The diameter (in millimeters) of the imaginary circle passing through the center of the chainring bolts on a crankset. Common vintage road standards include 144mm (Campagnolo Record/Super Record, Sugino Mighty, early Dura-Ace, SunTour Superbe), 135mm (Campagnolo C-Record onward), 130mm (Shimano Dura-Ace 7200/7400 onward, late Superbe Pro), 122mm (Stronglight 93), and 110mm (touring/compact). For 5-bolt cranks, BCD = Adjacent Bolt Center-to-Center Distance × 1.701.

Bar-end Shifter

General & Standards

A style of shifter which is usually mounted at the end of the drop section of handlebars. They are also mounted at the end of Aerobars on Time-Trial bikes. There have also been adapter-pods made which convert downtube-shifters into bar-end style shifters.

Barcons

General & Standards

SunTour registered name for Bar-End shifters.

Bicycle Geometry

General & Standards

Bicycle Geometry: The several angles and measures that comprise the construction and configuration of the bicycle frame and fork. Different configurations are used to construct frames for touring, road racing, track racing, cyclocross, keirin, and other riding styles. See Wikipedia (URL: http://en.wikipedia.org/wiki/Bicycle_and_motorcycle_geometry) for a source on bicycle geometry. Key terms include: Fork Rake, Trail, Wheelbase, Fork Offset, and so forth. See also the Wiki Bike Geometry Project at URL: http://home.comcast.net/~pinnah/dirtbag-bikes/geometry-project.html, which is still under construction, but available.

Biopace

General & Standards

Registered name for the Shimano style of non-round chainring produced by Shimano during the late 80's. Its purpose was to reduce knee strain and increase traction during off-road use. HP (High Performance) was the last version. It was closer to circular to allow higher cadence.

Bottom Bracket

General & Standards

(abbreviated to BB)(1) The part of the frame around which the pedal cranks revolve, also know as the BB shell.(2) The spindle and bearing assembly that runs through the bottom bracket shell of the frame. Both "spindle" and "axle" are used, people fight about which is correct.Varieties of Bottom Brackets: The traditional discrete cup & cone style has six parts: - two bearing cups which screw into the bottom bracket shell of the frame- a lock ring to lock the non-drive side cup in place, the spindle incorporates two cone bearings- two sets of balls (loose or caged, usually 1/4", 9 per side) which allow the spindle to turn freely on the cups. In first world countries this design is now only made for track use, with the ISO square taper. Otherwise replacements are either used or new-old-stock (NOS). The 2nd? & third world are still producing discrete BBs in volume with either square or cotter pin interfaces. Note that discrete BBs often have the drive side protruding an extra 1mm-8mm, whereas cartridge BBs have 0-1mm extra in the longer lengths. This must be checked and compensated for when replacing a discrete BB with a cartridge or else the chainline will be changed. Cartridge bottom brackets have only two visible parts, the cartridge and a retainer cup. The catridge is screwed in from the drive side of the frame, and the retainer cup steadies the non-driveside. Crank interfaces are square taper (JIS taper, except most track and euro makers use ISO); ISIS, and the proprietary Shimano Octalink and Truvativ Powerspline. Old American-style "Ashtabula" One-Piece Crank (OPC). In these the crank arms and spindle are one piece which run through the cups which are screwed into the bicycle frame. The lock nut and the cone behind it have a left-hand thread. Because the arms must be threaded through the frame these bottom bracket shells have a wider diameter than the 3-piece cranks above. These are still widely used for BMX, children's and very cheap bikes since they are rugged and tolerant of crude machining. Two piece cranks a.k.a integrated a.k.a. external-bearing cranks have been popular on high-end bikes since 2006. These use a fat tubular spindle integrated into the driveside crank. With traditional English or Italian BB shell the fat tube leaves no room for bearings so outboard bearings are used. These demand much more accurate shell thread alignment than earlier designs, so retrofitting to an older or cheaply made bike without having the frame "faced and chased" with specialist tools may result in very disappointing bearing life.

Brifter

General & Standards

The colloquial term for shifting brake levers, typically the ones seen on road bikes. These systems typically require the rider to rotate the brake lever inwards to shift to a lower gear, and have a second lever, either behind the brake lever or under the rider's thumb, to shift to a higher gear. Shimano uses the prefix ST to differentiate these from their brake levers (BL) and their shifters (SL). This site use the term "Shifting Brake Levers"

British

General & Standards

British dimensions have mostly been adopted by the I.S.O. These standards include: 1" x 24 tpi headset thread 1" (25.4 mm) handlebar/stem clamp diameter 1.375" x 24 tpi bottom bracket threading (left-hand on the fixed cup). These are not the same as Raleigh dimensions 1.375" x 24 tpi freewheel thread 56 TPI spoke thread

Brooks

General & Standards

Is world's foremost producer of leather saddles. Based in England, Brooks is one of the oldest companies in the bicycle industry. Their most popular model is the famous B-17 which is produced in several versions including a narrow B-17N and the Champion Special versions using copper rivets and specal colored leather. Brooks models range from very wide sprung saddles to the Titanium railed Swift and Swallow racing saddles.

Captain

General & Standards

The front rider of a tandem (see also > Stoker)

Chainring

General & Standards

The front sproket, typically bolted to a crank spider to make a crankset. Chainrings come in many different BCD (Bolt Circle Diameter) and you must match the chainrings BCD to that which the spider is made for. Measuring from the center of one hole to the center of the next hole, you can determine the BCD of the chainring or spider. Here is a table for the conversion: Distance (x) BCD 5 hole chainrings 34.3mm 58mm 43.5mm 74mm 55.4mm 94mm 64.7mm 110mm 71.5mm 122mm 76.4mm 130mm 79.5mm 135mm 84.6mm 144mm Distance (x) BCD 4 hole chainrings 41.0mm 58mm 45.3mm 64mm 48.1mm 68mm 73.6mm 104mm 79.2mm 112mm

Chainstay

General & Standards

The narrow tubes that extend from the bottom bracket to the rear dropouts.

Chamois

General & Standards

KrogerExperiencee Sweepstakes/Rewards Page and take Kroger Experience Survey to Win 50 free fuel bonus points and 100$ gift card.. https://krogerexperiencee.com/greatpeople-me-kroger-employee-login-portal

Chorus

General & Standards

Campagnolo's second line component group introduced in the late 80's.

Claw Hanger Adapter

Drivetrain

A stamped steel adapter bracket attached to a rear derailleur that slips into a horizontal rear dropout slot and is secured by the axle nut and a crescent locator bolt, allowing derailleur installation on frames manufactured without an integral forged derailleur hanger.

Cleat

General & Standards

Cleat: Device fitted to the sole of the cycling shoe to securely and properly place and hold the cycling shoe on the pedal over the pedal axel.

Clipless

General & Standards

Clipless pedals and shoes are somewhat misleading, because they allow a rider to attach their feet to their pedals, using a clipping system. This name is due to the fact that the previous method of attaching one's feet to the pedals (in a small, cage-like structure that would cover the rider's toes) was known as "toe clips". The new-at-the-time technology which did not require toe clips was then dubbed "clipless". The term "flat pedals" is typically used when talking about pedals with no clipping system whatsoever.

Cog size

General & Standards

Cog Size: The number of teeth on a freewheel cog or sprocket.

Cold Set

General & Standards

To change the shape of a piece of metal without heating. This term is most often used in relation to changing the width of the rear dropouts of a bicycle frame in order to accept a different wheel hub width. Cold setting a frame's dropouts from 120mm to 126 allows one to use a 6 or 7speed wheel on a bicycle originally built for 5speed freewheels. Likewise spreading from 126 to 130 allows you to use modern 8, 9 or 10sp setups on older frames. There are two common ways of cold setting a bicycle frame's rear drop outs. 1) The threaded rod method and 2) the lumber method. 1) Threaded Rod Method: The threaded rod method utlizes a long threaded rod (longer than the width of the drop outs by at least 5-6cm), a number of large fender washers and nuts. The idea is to place the nuts and washers on the threaded rod in an arrangement to where you can slowly force the dropouts further apart by turning the nut. Do this in small incriments to insure you don't go too far, but you will need to go far beyond the desired final width as the steel will spring back. 2) The lumber method follows the following steps: 1) Lay the bicycle on its side with the handlebars turned to face upward. 2) Insert the lumber through the rear triangle, so that it goes underneath the upper rear fork end, and above the seat tube. The lumber should extend out past the rear end of the frame. 3) Place the far end of the lumber onto a chair, crate or other raised structure, so that only the head-tube/fork area of the bike is in contact with the floor. 4) Press down gently on the lumber where it crosses on top of the seat tube. 5) Measure to see if any change has been made. 6) Repeat until half of the desired change in width is achived. 7) Flip bicycle over and do the same on the other side to achieve the final desired width. Notes: Never attempt to cold set an aluminum or cabon framed bicycle. Trying to attach a magnet to a frame will very quickly let you know if it is steel or not. If it doesn't stick don't cold set. There is a possiblity of damaging your frame during cold setting if you are not careful through the process. Tying of twine very tightly around the brake bridge will help ensure that the bridge does not pop off one of the stays. SheldonBrown.com has a more extensive write up on this topic.

Columbus

General & Standards

Italian maker of steel tubing which bicycles were made from. The most common models of Columbus steel tubing found on vintage bicycles were (from lower to higher grade) SP, SL, SLX.

Cottered Crank

General & Standards

An older way of attaching a crankset to the spindle of the bottom bracket. They use cotters (wedge shaped pins with a threaded end for a nut) to firmly attach the crank arm to the spindle. Removing cotters can be difficult and time consuming without the proper tools. Cottered cranks gave way to cotter-less cranks which use a bolt threaded into the bottom bracket spindle to hold it in place.

Criterium

General & Standards

Criterium: Bicycle race covering a short course, frequently in a city or neighborhood, consisting of a number of predetermined laps, or circuits following the same route. The race ends when the total number of laps or the predetermined distance has been covered by the first rider.

Crown

General & Standards

The upper part of the front fork where the fork blades and steerer tube are attached together. The crown race of the headset sits directly above the fork crown.

Derailleur

General & Standards

The mechanism which moves a bicycle's chain from one chainring or sprocket to another. They are typically mounted on the seat tube directly above the crankset, and on the end of the drive-side rear dropout below the gear cluster. The first derailleurs were created by Campagnolo, and consisted of a pivoting rod running along the seat stay. Today nearly all derailleurs function by moving cables via a lever of one design or another.

Down Tube

General & Standards

The tube which runs from the headtube at the front of the bike down to the bottom bracket shell. Typically where the shifters are mounted on many vintage lightweight bicycles, thus the name downtube shifters.

Drainpipe

General & Standards

A term used by framebuilders that describes the tube connecting the bottom bracket shells of a tandem.

Drop Out

General & Standards

A type of rear fork end that allows the wheel to be removed without derailling the chain first. Found on most multi-geared bicycles. Track and BMX bicycles do not have dropouts, instead they have rear facing fork ends. Dropouts come in two main designs, the horizontal and vertical style. The horizontal style was most popular up through the late 1980's where it started to give way to vertical dropouts. It is possible to mis-align the rear wheel with horizontal dropouts either during wheel installation, or during use if the rear wheel is not tightened well enough. "Horizontal" dropouts are actually angled downwards. During wheel removal this allows the tyre to move past the brake, and helps it clear the seat tube. It avoids the need to reset the brake height if the wheel is moved forward or back, and helps retain the wheel if the axle comes loose on a bumpy downhill. Looking at the rear drop outs is one way to gauge the quality of a bicycle. Many (but not all) high quality bicycles, especially from the late '70s on, have forged dropouts with integrated derailleur hangers. Cheaper bikes generally have stamped steel dropouts which usually require a separate, claw-style derailleur hanger.

Dropout Adjusters

General & Standards

Dropout adjusters are screws found on some forged horizontal dropouts. They allow for quick, consistent placement and alignment of the rear axle during wheel changes / maintainence.

Dura-Ace

General & Standards

Shimano's top-of-the-line groupset for the last several decades.

E.R.D.

General & Standards

Acronym for Effective Rim Diameter. Used primarily for spoke length calculation, this value is the rim's diameter at the nipple seats. Depending on the rim's design, it can vary considerably from the inner diameter.

Extension Levers

General & Standards

Bolt-on extensions to drop bar brake levers which allow the operation of the brake from the tops of the handlebars. Common on low to mid range bicycles of the "Bike Boom" era of the '70s and '80s. Initially developed by Dia-Compe, they're often seen on Dia-Compe and Weinmann brand brake levers. Although known as "safety levers", many people consider them a step backward in safety; they are commonly referred to as "turkey wings", "suicide levers" and other less flattering names. The levers do have several drawbacks including: Partially engaging the brake lever, thus reducing its available travel distance. Attachment hardware can make it difficult if not impossible to use the top hood hand position while riding. Encourages the use of the top-middle hand position on the handlebar which doesn't provide solid, secure control of the bicycle.

Ferrule

General & Standards

The metal or plastic fitting that slips over the end of a cable housing. It prevents damage, and provides a solid base against the cable stop.

Flute

General & Standards

A milled groove or group of grooves for decoration and lightening of a component. Most often on crank arms, crank spider, or the upper section of a seat post. Fluted seatposts which are set low enough to collect water in the flutes require especially diligent greasing of the seat tube to avoid filling the BB with water, and rusting the seat post in place.

Frame Size

General & Standards

Most bicycles are sized by the length of their seat tube. This measurement is usually either the "center-to-center" (c-t-c / ctc / c-c) length, or "center-to-top" (c-t-t / ctt) length. Center-to-center measures the length from the center of the bottom bracket shell to the center of the junction of the seat tube and top tube. The difference between these two measurements can be anywhere from half an inch to several centimeters, depending on the design of the frame and the meaning of "top". Center-to-top is the measurement from the center of the bottom bracket shell to one of two possible locations:(1) Where the top of the seat tube would be on a traditional frame, i.e. level with the top of the horizontal top tube. If the top tube slopes a virtual horizontal top tube may be used. For a given rider this allows comparison of the vertical distance between the seat and the top of the head tube between different bikes. (2) The actual top of the seat tube, which on modern bikes includes an extension of widely varying length above the top tube. This measurement is very useful when jamming a child onto the largest bike he/she can possibly ride (to allow for growth); and because it is very easy to measure. It is used by several brands despite its irrelevance to adults. Horizontal top tube length is also often given as a secondary measurement, always measured c-c. Standover height is not an issue for most riders but it can be important for generously sized trad frames (especially MTB and tourers), very small bikes, and children. Standover should be measured at least 30cm forwards of the saddle point, keeping in mind that riders often stand in front of the cranks so are even further forward. Frame size cannot be directly translated into its standover height, due to differing bottom bracket heights, and even tire size choice.

Friction Shifting

General & Standards

A shifting device which operates smoothly throughout its travel. It does not have indexed stops to aid the rider in finding the exact position for each gear change. The rider must learn how far to move the lever to shift into a different gear, manually aligning the jockey wheel or front derailleur cage. Friction shifting gave way to indexed shifting on lightweight bicycles during the mid- to late '80s.

Gain Ratio

General & Standards

A way of calculating a bicycle's gear ratio[s] proposed by Sheldon Brown, taking crank arm length into account.More information on this system can be found here: http://www.sheldonbrown.com/gain.html

Gear Ratio

General & Standards

The numeric representation of the differences between the sizes of the crankset chain wheels and the cogs on the freewheel. Gear ratios are normally expressed in terms of mechanical advantage by gain ratios or gear inches. See Sheldon Brown's comprehensive discussion at URL: http://www.sheldonbrown.com/gain.html.

Gears

General & Standards

Gears: Wikipedia (http://en.wikipedia.org/wiki/Bicycle_gear) has a very useful article discussing aspects of gearing; particularly that involving freewheel cog set-up in conjunction with crankset chain ring set-up size. One traditional set-up for chain rings on a vintage crankset is 52 tooth/42 tooth. The corresponding size of the cogs on the freewheel make up the gearing profile of the bike. As noted in the referenced Wiki article… The relative difference between two gears is more important than the absolute difference between gears. The relative change, from a lower gear to a higher gear, is normally expressed as a percentage. Cycling tends to feel more comfortable if nearly all gear changes have more or less the same percentage difference; a larger percentage difference may be acceptable for lower gears where the absolute difference is not too large. A step of 7% corresponds to a 1-tooth change from a 14-tooth cog to a 15-tooth cog, while a step of 15% corresponds to a 2-tooth change from a 13-tooth cog to a 15-tooth cog. Vintage bikes are usually set up with a double (road) or triple (touring) chain ring crankset, coupled with a 5-speed, 6-speed, and later into the 80s, a 7-speed freewheel. Selection of which freewheel to use, or the set-up of the freewheel cogs, often involved what type of cycling was being undertaken. Sheldon Brown has an excellent article discussing various aspects of gearing and gear selection at URL: http://www.sheldonbrown.com/gear-theory.html.

Group

General & Standards

A group of bicycle parts which are sold together from one manufacturer. The parts are designed to work together, and usually have similar styling and finish. A group normally includes the following parts: Brakes, Brake Levers, Shifters, Cranks, Bottom Bracket, and Derailleurs. It can also include other parts including Pedals, Headsets, Seat Posts and Chains.

Head tube

General & Standards

The part of the bicycle's frame which the front fork's steerer tube is inserted through.

Headset

General & Standards

The bearing set which connects the front fork to the frame. Vintage bicycles typical use what is known as a threaded headset including (from top to bottom): Lock nut threaded to steerer tube. Spacer / Washer, usually keyed to slot in steerer tube. Upper Race threaded to steerer tube. Upper bearings Upper Cup inserted into top of head tube Lower Cup inserted into bottom of head tube Lower bearings Crown Race seated against the crown on the steerer tube Some headsets swap the position of the upper cups and races depending on design. Determining which goes where look for which is threaded.

Hi-Ten

General & Standards

Short for Hi-Tensile steel, or high carbon steel. This is at the far heavy end of steels used for bicycle construction. 1020, 2040 and similar steels all fall in this category. A bicycle made completely of Hi-Ten steel can easily weigh 28-32 lbs or more.

Hood

General & Standards

The part of the brake lever which attaches to the handlebar. This part remains stationary while the attached lever is moved to apply the brakes. This part is usually covered in rubber to pad and insulate the area for use as a hand position.

ISO vs. Italian Bottom Bracket Threading

Standards & Threading

English/ISO bottom bracket shells are 68mm wide with 1.370" x 24 TPI threads (Drive-Side/Right cup is LEFT-hand threaded; Left cup is RIGHT-hand threaded). Italian bottom bracket shells are 70mm wide with 36mm x 24 TPI threads (BOTH cups are RIGHT-hand threaded). French shells (68mm) use 35mm x 1mm metric threads (both right-hand threaded).

Indexed Shifting

General & Standards

Indexed shifting systems utilize a series of clicks or stops to provide precise shifts from one gear to another. This allows the rider to make quick trouble free shifts without the worry of having the derailleur end up between gears resulting in noisy and rough chain operation. Indexed shifting started to catch hold in cycling during the mid to late 80's. Shimano was the first company to successfully introduce Indexed Shifting, and within a few years was able to gain significant market share over SunTour and Camapgnolo due to this innovation.

Infinity

General & Standards

A medium quality tapered, seamed double-butted Cr-Mo tubeset manufactured by Tange Industries from the late 80s. The seam allowed precise tapering between the thick and thin sections to be done cheaply. The Japanese had reduced the weakness traditionally found in seamed tubes, making reasonably light bikes affordable to many.

Ishiwata

General & Standards

A Japanese manufacturer of quality steel tubesets. Closed in the early 1990s.

JIS vs. ISO Square Taper

Drivetrain

Both JIS (Japanese Industrial Standard — Shimano, SunTour, modern Sugino) and ISO (Campagnolo, Stronglight, Mavic, vintage Sugino Mighty) square-taper bottom bracket spindles use a 2-degree taper per face, but JIS has a slightly wider tip (~12.65mm vs ~12.5mm for ISO). Installing an ISO crank on a JIS spindle sits ~4.5mm further outboard; installing a JIS crank on an ISO spindle sits ~4.5mm further inboard and may bottom out.

Japanese Industrial Standard (JIS)

General & Standards

A well-defined set of standards adhered to by Japanese and Asian manufacturers.Headsets: JIS is found on many lower-to-middle grade bicycles produced during the bike-boom in Japan and other asian countries. It is possible to convert a bike built for JIS headsets to ISO (Campagnolo) standards with grinding to the head tube and fork steerer tube. JIS fork crown seats are 27.0 mm in diameter, vs ISO 26.4 mmJIS head tube inside diameter is 30.0 mm, vs ISO 30.2mm Square taper bottom brackets: JIS BBs are slightly fatter than ISO. ISO taper is used worldwide for track components, and is used by european manufacturers.

Keyed Washer

General & Standards

A keyed washer is a washer with a special-shaped hole that fits over a special shaft. It can slide down the shaft, but not turn. The usual set up is to have a groove in the axle or shaft, and a washer's hole will have a small tab that fits into the groove. This is almost always used in headset and pedal bearings and sometimes in hub axles such as the Campagnolo Record hub. This allows you to tighten the lock nut above the washer without moving the cone under the washer keeping the same level of pre-load during final assembly.

Krate

General & Standards

Schwinn trademark for a family of wheelie bikes. These have become quite valuable to collectors.

Lightweight

General & Standards

Traditionally a term for bicycles designed to use tires of width 1.5 inches or less. Racing style bicycles, as well as long distance touring fall into this category.

Lock Nut

General & Standards

A nut which is tightened against another nut to keep it from loosening up. Often, but not always, there will be a key washer between the lock nut and the cone or other part it secures. Lock nuts are used to secure bearing adjustment of most hubs, headsets, pedals and sidepull brakes. Most hubs use lock nuts to secure the cones so that they will stay in adjustment. These lock nuts are the outermost parts which are screwed onto the axle, and their outer surfaces press against the insides of the fork ends of the frame. The lock nuts are therefore the reference point by which axle width and dishing are measured.

Lug

General & Standards

Lugs are a socketed joint used in bicycle construction to join two or more pieces of tubing together. The best lugs are cast. Others are made from pierced tubing or from welded sheet.In lugged steel bicycle construction these lugs and the tubes are joined with brass or silver brazing. Skill is needed to complete the joint with minimal heat, since heat weakens the tubing.After brazing the lugs may be filed to reduce stress in the tubing at the lug edge.It was very common for these lugs to be cut in ornate and distinctive designs, with single or multiple points, cutouts, etc. In the late 1980s new steels which could withstand TIG welding became popular for low and midrange bikes, and eventually the top steel tubesets were weldable. By that time (early-mid 1990s) most top-end bikes had moved away from steel anyway. Glued aluminium lugs have been used to join unweldable grades of aluminium, or precut carbon tubes, or steel stays.

Milled

General & Standards

A process which cuts material away from a cast or forged piece of metal. Milled grooves are often called flutes which are often found on cranks and seat posts.

Mixte

General & Standards

A mixte frame (sometimes written and pronounced 'mixtie') is a unisex frame which traditionally has twin top tubes, running from the top of the head tube all the way back to the rear axle. This gives an elegant 'arrowhead' design. The mixte style frame is considered to be less stiff, therefore more flexible, than a traditional 'diamond' frame. The mixte frame has the advantage of retaining the advantage of a lowered top tube (allowing riders with less flexibility to ride), but without the drawbacks of a 'ladies' step through frame (additional stress placed on the seat tube and also being slower and heavier).

Nipple

General & Standards

Specialized nut which connects a rim to the spoke in a bicycle wheel. To remove, first remove all tension from the spoke and then remove from the outside of the rim.

Nuovo

General & Standards

Italian for "New". Most often seen in the Camapgnolo groups Nuovo Record, Nuovo Gran Sport and Nuovo Tipo.

Nuovo Record

General & Standards

One of Campagnolo's top component group for many years in the 60's and 70's and 80's.

OLD (Over-Locknut Distance)

Wheels & Hubs

The external width of a hub axle measured between the outer faces of the two locknuts where they bear against the inside of the frame dropouts. Standard vintage rear road spacings are 120mm (5-speed era, pre-1978), 126mm (6/7-speed era, 1978–1989), and 130mm (8-speed+ road era, 1989+); front road hubs are almost universally 100mm.

OLN

General & Standards

Over Lock Nut(s). Used in measuring the spacing of a wheel, as in measured 126mm OLN.

Oxalic acid

General & Standards

Not quite a wonder drug, but very useful in helping get rust off steel parts/chrome. See this link: http://www.vintagebmx.com/cgi-bin/ultimatebb.cgi?ubb=get_topic;f=4;t=004702

Pannier

General & Standards

Pannier: Front and/or rear bags attached to the bicycle on racks that are fitted to the frame. Panniers are used by touring cyclists to carry equipment and supplies to be used on extended tours.

Pantographing

Framebuilding & Finishing

Mechanical engraving of a framebuilder's crest, signature, or geometric recesses (e.g., Colnago clubs, De Rosa hearts, Bianchi eagles, Eddy Merckx 'E' emblems) into alloy stems, chainrings, seatposts, and shift levers using a tracer-guided milling pantograph, typically hand-filled with colored enamel paint.

Presta

General & Standards

The narrow valve used on most high-performance vintage bicycle wheels, and all tubulars wheels. Presta valves have built-in valve caps, which must be opened before you can inflate them. Since there is no spring in a Presta valve, this knurled nut must be tightened after inflating the tire, or the valve may leak slowly. Presta valves are lighter weight than schrader, and don't require as large a hole in the rim.

Prestige

General & Standards

The highest grade of tubing made by Japanese tubeset manufacturer Tange Industries.

Q-Factor

General & Standards

"Q-factor" is the horizontal width between the outside of the cranks' pedal holes, normally given in mm. Q depends on both the axle length and the crank's shape. To keep it narrow can be important for aerodynamic properties, but to lessen pain in the knee or hip it should correspond to the rider's hip width. French crank manufacturers as Stronglight and T.A. are known for narrow Q-factors ("Facteur Q") and they used to mention it as a product feature. Front derailleurs with sculpted cages (post 1990ish) require more space between the right crank and the chainwheel, increasing Q. Mountain bikes' wider rear hub/chainline, wider tyres and mud clearance requirements require wider chainstays, forcing a wider Q than would be ideal on a road bike. DERIVATION Increasing Q does increase the bike+rider's aerodynamic form factor, but not linearly so it is not a factor in the physical/mathematical sense implied by "Q". "Factor" means a number, quantity or even a function which is multipled by. Possibly the term "Q-factor" was borrowed from the field of radio electronics back when that was in vogue. In radio Q is short for Quality of a resonant circuit. Omitting the word "factor" from the borrowed term is acceptable, and it is especially considerate to do so when in the presence of pedants or engineers.

Quill

General & Standards

The vertical part of a stem built for threaded headsets, having a expander or wedge of some sort to secure the stem inside the fork's steerer tube. Traditional style of pedal which uses toe-clips and straps are often known as quill pedals for unknown reasons.

Quill Stem Diameter (22.2mm vs. 22.0mm French)

Cockpit

Standard ISO/English/Italian 1-inch threaded fork steerer tubes have an internal diameter of 22.2mm (7/8 inch). Vintage French bicycles (Peugeot, Gitane, Motobécane prior to the mid-1980s) used metric 25mm O.D. steerer tubes with a 22.0mm internal diameter, requiring a 22.0mm quill stem.

Rattrap Pedals

General & Standards

The classic vintage pedal. Generally with 'teeth' on both top and bottom, rattrap pedals were used on racing bikes, as the teeth allowed riders to have a better grip. Toe clips and straps were often used with rattrap pedals, allowing for more efficient use of the rider's energy. See: Campagnolo Pedals Component Listing

Recessed Brake Mounting

General & Standards

A brake mounting design which utilizes a 5mm allen key nut (hole is 6mm in diameter) which fits into the fork crown and rear brake bridge to secure the brake to the frame. This is a cleaner design than the older style of using a standard nut on the end of a longer brake bolt. Shorter studs are required on the brakes e.g. 13mm rear.To regain the ability to attach & detach mudguards without disturbing the brake a Sheldon nut can be used. This has a longer head with a smaller threaded hole drilled into it, and the mudguard bolt passes through the Allen head.

Recessed vs. Nutted Brake Mount

Brakes

Pre-1978 road frames use a 6mm hole through both walls of the fork crown and rear brake bridge, with an exposed hex nut on the back ('Nutted mount', requiring longer center bolts). Around 1978, Campagnolo and Shimano introduced 'Recessed Allen' mounting, where the rear face of the fork crown/bridge is drilled to 8mm to accept a flush tubular sleeve nut tightened with a 5mm Allen key.

Record

General & Standards

Campagnolo has used the Record name for their top of the line component groups for much of their history. ie: Record, Nuovo Record, and Super Record.

Renak

General & Standards

Country: Germany (DDR at the time) Renak stands for Reichenbacher Naben- & Kupplungwerke. This was a Fichtel & Sachs (F&S) plant that was set up in 1942/3 in Reichenbach (near Chemnitz the home of Diamant, East Germany’s leading bicycle producer). After 1945 this plant became a separate business (VEB) when Reichenbach became part of the DDR. VEB stands for ‘Volkseigener Betrieb’ (‘organisation owned by the people’), and was the standard form of state owned business in the DDR. From about 1949 this business used the FuS brand, implicitly standing for ‘Fichtel und Sachs’ but being ever so slightly different from ‘F&S’. In 1954 it decided to stand on its own two feet and replaced the FuS brand with the Renak brand.Renak manufactured a range of bicycle components, particularly standard hubs and back pedal brake hubs and exported them to over 40 countries. Renak seems to have been a supplier of pull-chain derailleurs to Diamant from 1950 to the mid 1970’s (according to some claims). Diamant may have moved from Renak derailleurs to Tectoron models in the mid 1970’s. In 1990 Renak was privatised by the Treuhandanstalt and sold to the Tianjin Flying Pigeon Bicycle Co. Ltd, a famous Chinese bicycle manufacturer. Some employees from Renak started up a new company, using the Renak name, that manufactures a compact hub dynamo, and after a series of moves this company is now based in Itzehoe in northern Germany.

Retrofriction

Drivetrain

A clutch-spring mechanism pioneered by Simplex (and later used by Mavic and Campagnolo Doppler shifters) inside a friction shift lever. A tightly wound coil spring wraps around the pivot cylinder so pulling the lever against rear derailleur spring tension releases clutch drag (light lever feel), while derailleur pull in the opposite direction tightens the coil spring to prevent slippage.

Reynolds

General & Standards

Reynolds, now under the name TI/Reynolds, is an old and very highly regarded maker of bicycle frame tubing. Reynolds pioneered the techniques of making butted tubing, and the 531 tubing was the standard of excellence for many decades until the development of 753. Other grades of steel from this builder include the heavier but weldable 501 steel, and the newer and lighter 853 and 953. Nearly any bicycle with a Reynolds tubing sticker is worth considering.

Rim Tape

General & Standards

Rim Tape: Fabric, plastic, or sometimes rubber tape that is placed on the inside of clincher rims to protect the tube from irritation and punctures caused by protruding spoke tips or sharp ferrule edges. Some brands are made of combinations of materials, such as fiber-reinforced plastic, and some have adhesive on one side to stick to the rim, while others are held in place solely by tension.

SIS

General & Standards

Shimano Indexing System. Shimano's first generation indexed shifting system, the first to achieve commercial success. The introduction of SIS ahead of Campagnolo and SunTour's indexing system allowed them to gain large amounts of market share in the mid to late 80's.

Schrader

General & Standards

Standard automotive-style air valve. Many low to medium grade 'bike-boom' bicycles produced in the US or for the US market came equipped with wheels made for this type of valve. Includes an internal spring forcing it to be a wider and heavier valve design than presta valves.

Seat tube

General & Standards

The tube of a standard bicycle that runs from the bottom bracket up to the seat lug, or the point at which it merges with the seatstays and the top tube.

Seatstay

General & Standards

The tubing pieces of a bicycle that run from the rear dropout where the rear wheel is attached, up to the junction of the seat tube and top tubes. The rear brake is attached to a small bridge attached to the seatstays or directly to the seatstays.

Sew-Up

General & Standards

Another name for Tubular tires.

Slant Parallelogram

Drivetrain

Patented by Maeda SunTour in 1964 (invented by Nobuo Ozaki), a rear derailleur geometry in which the parallelogram body is angled downward parallel to the slope of the freewheel cogset. This maintains a consistent chain gap across every sprocket for dramatically crisper shifting. When SunTour's 20-year patent expired in 1984, Shimano immediately adopted the slant parallelogram for Dura-Ace 7400 SIS.

Spider

General & Standards

The center part of a crankset to which chainrings are bolted to. The spider is then mounted on the spindle of the bottom bracket on the bicycle. Also an aluminium frame used to hold the larger sprockets of a rear cassette.

Sprocket

General & Standards

Sprocket: A cog, either single or part of a freewheel, or chain ring that meshes with the drive chain.

Stem

General & Standards

The stem is the part of the bicycle which connects the handlebars to the bicycle's fork. Most vintage bicycles have what are known as Quill Stems. These are inserted down into the forks steerer tube and then held in place by a wedge. The handlebars are typically held in place by a clamp bolt.

Stoker

General & Standards

The rear rider of a tandem (see also > Captain)

Super Record

General & Standards

One of Campagnolo's top component groups from the mid 70's through the mid 80's. First group to introduce Titanium to the Campagnolo line up.

Syncro

General & Standards

Campagnolo's early Indexed Shifting design name. Downtube shifters had a lever that could be moved to turn the shifter back into a friction shifter. Which was often used due to the difficulty in getting the system to shift properly.

Tange Industries

General & Standards

One of Japan's largest producers of steel tubesets, as well as a limited range of components such as headsets and seatpost clamps. Their tubing was used by many of Japan's largest bicycle makers, such as Nishiki, Apollo, and Centurion.

Tire Iron

General & Standards

Tire Iron: Also known as "tire levers"; a tire iron is a tool that usually comes in a set of two or three that is used to remove clincher tires from the tire rim. Photographs are recorded in the Tool Database.

Toe Clips

General & Standards

Toe Clips: Device added on to the front cage of cycling pedals that curve up and over the cycling shoe to assist holding the foot to the pedal, especially when pulling up in the pedal stroke. Adjusted by using toe clip straps with quick-release buckles for fast adjustment.

Top tube

General & Standards

The tube on a standard bicycle that runs from the seat lug to the head lug. On the vast majority of vintage lightweights, this tube runs parallel to the ground, though many modern bikes have a top tube that slopes down toward the rear of the bicycle.

TrueTemper

General & Standards

An American manufacturer of bicycle tubing, used by Trek, DiamondBack, and other American bicycle manufacturers.

Truing

General & Standards

Maintaining the balance of a wheel’s spoke tension so that the wheel is round and centered on the axel. Truing is accomplished by carefully adjusting the tension of the spokes by tightening or loosening the spoke nipples. On the Internet, see Sheldon Brown’s comprehensive discussion on wheel building and truing at URL: http://sheldonbrown.com/wheelbuild.html.

Tube Investments (TI)

General & Standards

This large conglomerate, parent company to British Cycle Corporation, bought Raleigh Industries in 1960 and merged Raleigh with the B.C.C. brands Philipps, Hercules, Norman and Sun.

Tubular (Sew-Up / Boyau)

Wheels & Hubs

Traditional racing tire construction in which a latex or butyl inner tube is sewn completely inside a cotton or silk casing, which is then glued with mastic cement onto a shallow concave box-section rim lacking bead hooks.

Turkey Wings

General & Standards

See Extension Levers.

Ultegra

General & Standards

Shimano's second-from-the-top (below Dura-Ace) groupset, from the mid '90s into the present. It's lineage is: 600 6speed friction. (6200)600AX 6 speed Positron indexed aero group. (6300) 1982-83600EX 1984-87 600 Ultegra (6400) 7 speed indexed. 600 Ultegra (6401) 8 speed, STI and DT shifters.Ultegra (6500) 9 speed 1998-2004Ultegra (6600) 10 speed v1 2005- (this is the last version fully compatible with earlier derailleurs and brakes)Ultegra (6700) 10 speed v1 hidden gear cables. Brake calipers have more leverage, levers have less. FD throw increased. All parts still usable with older gear.Ultegra (6800) 10 speed

Uniglide (UG) vs. Hyperglide (HG)

Drivetrain

Shimano Uniglide (1978–1988) cassette freehubs use 9 equal-width splines and have external threads on the end of the freehub body; the smallest sprocket is threaded and screws on to lock the remaining cogs in place. Hyperglide (introduced 1988/1989) uses one wide master spline for cog timing alignment, shift ramps/gates, and an internal thread for a separate lockring.

VLW

General & Standards

Stands for Vintage Lightweight. Lightweight bicycles are traditionally those designed to use a tire of 1.5 in in width or less. These include racing and most touring style bicycles. Vintage Lightweights are typically considered those built during the 1980's or earlier.

Vitus

General & Standards

Major French manufacturer of steel tubing used in bicycle frames. In the 80's they moved into aluminum tubing as well.

Wheel Building

General & Standards

See truing. A wheel is built using a rim, spokes and nipples, and a hub. For a comprehensive guide, see Sheldon Brown’s tutorial on wheel building and truing at URL: http://sheldonbrown.com/wheelbuild.html.

Wheelbase

General & Standards

Wheelbase: The horizontal distance between the center point of the front wheel axel and the center point of the rear wheel axel. Note that Wikipedia is an excellent source of information on bicycle geometry. See URL: http://en.wikipedia.org/wiki/Bicycle_and_motorcycle_geometry.

cog

General & Standards

Cog: A gear, either single or part of a multi-geared freewheel, with teeth that mesh to a drive chain. A sprocket.

randonneur

General & Standards

Randonneur: (1) Bicycle used for a long distance non-racing event known as a "randonée" or "brevet". (2) A rider in such an event. Originating in fixed-pace Audax events, the randonée allows riders to choose their own pace between checkpoints, within limits of e.g. 15 and 30kph. Any bike can be used but the ideal is part way between a racer and a light tourer. Distances are 200km - 1200km so the quick steering, low crouch and hard, delicate tyres of a racer may become tiresome, as may the lack of mudguards. Riders are self-supporting so will have some luggage capacity.