Shimano RD-7402, Dura-Ace (8sp)
Manufacturer: Shimano • Group: Dura-Ace 7400 • Model: RD-7402 • Part ID / SKU: RD-7402
✓ Verified PhotoClick to Enlarge & Zoom| Category: | Rear Derailleurs |
|---|---|
| Name: | Shimano RD-7402, Dura-Ace (8sp) |
| Brand: | Shimano (Japan) |
| Primary Group: | Dura-Ace 7400 (Mid 1980's - Late 1980's) |
| Model: | RD-7402 |
| Part ID / SKU: | RD-7402 |
| Years: | 1989 - 1996 |
| Country: | Japan |
| Weight: | 207.0g(7.30 oz) Note: 207 grams (avg)View Weight List |
| Quality Rating: | Excellent4.92/5 (12 votes) |
| Rarity Rating: | Uncommon3.38/5 (8 votes) |
| Max Cog [T]: | 26TRated Max Limit: 26T |
|---|---|
| Total Capacity [T]: | —Rated Capacity: 26T |
| Cage Length: | Short |
| Mount Type: | — |
| Shifting System: | — |
| Pulley Teeth: | — |
| Material / Construction: | Aluminum Alloy |
| Outer Plate Markings: | Dura-Ace |
| Inner Plate Markings: | Shimano RD-7402 VIA Japan |
| Design Category: | Slant parallelogram |
| Attachment Bolt Size: | 5mm Allen Key |
| Cable Attachment Bolt Size: | 5mm Allen Key |
| Shifting Systems: | Dura-Ace SISDura-Ace STIFriction |
| Cable Adjuster: | Yes |
| Max Chain Wrap: | 26Rated Capacity: 26T |
| Search by Traits: | ✓ Outer Plate Markings: Dura-Ace✓ Inner Plate Markings: Shimano RD-7402 VIA Japan✓ Material: Aluminum Alloy✓ Design Category: Slant parallelogram✓ Attachment Bolt Size: 5mm Allen Key✓ Cable Attachment Bolt Size: 5mm Allen Key✓ Shifting Systems: Dura-Ace SISDura-Ace STIFriction✓ Cable Adjuster: Yes✓ Cage Length: Short✓ Max Cog Size: 26✓ Max Chain Wrap: 26✓ Short Cage |
| Photo | Variation # | Component Variation Name | Model Code | Years Produced | Weight | Key Distinguishing Notes |
|---|---|---|---|---|---|---|
![]() | 1 of 1Viewing | Shimano RD-7402, Dura-Ace (8sp) | RD-7402 | 1989 - 1996 | 207g | Double Servo-Panta Mechanism, Centeron Guide Pulley, Sealed Pulley, Ceramic Pulley, Adjustable Return Spring, Sealed Pivot Axles (O-Ring), Sealed Link Pivots, B-Tension Adjuster. Added By: JFischer on 10/29/07 | Updated By: MGTS on 11/19/20 |
The last two photographs show fixing bolt changes, first photographs shows how rear derailleur is delivered, fixing bolt is accessed through parallelogram, which can be difficult. Second photograph shows how most people turned fixing bolt around for better accessiblity.
TIP: Getting the Dura Ace RD-7402 Derailleur to work with modern standard cable pull shifting levers: As most who have this derailleur know, the cable pull was shorter on these and modern shifters will not work. You generally need the mated shifters from that time period and group. I've been looking awile for the bar end shifter version, but no luck up to now. However, i just completed an "exception", and found it is indeed possible to get these working with modern shifters! :-) I'm using a Dura Ace 8-9 speed shifter, with the rear derailluer locking out the unused 9th gear with the low end stop screw. I had TWO of these wonderfully machined derailleurs sitting around, and wanted to put one on my late 1980's Serotta steel frame and run it as a 1X8 speed commuter. (had it set up fixed gear! :-) It was not an easy conversion, as i was working with several slightly used cassettes from Shimano and Sram. Some of the larger cogs i wanted to use were on a spider, and could not be used alone if separated. By mixing and matching cogs from differing cassettes, i was able to come up with usuable cogs of 12/13/14/15/17/20/23/26 , which is representitive of the outside extreme cog sizes for this derailleur. (12-26T) I figured "if" i could arrive at a proper spacer thickness, then i could get this deraillure to work with my later Dura Ace bar end shifter. (now mounted to a Paul "Thumbie") Because the deraillure is a bit short on it's movement with a modern shifter's cable pull, a smaller spacer than the 8 speed norm is called for. The workable spacer thickness for this derailleur proved to be a bit more than the average thickness of a nine speed (2.56mm or 0.100787 inch), and 8 speed spacer (3.0mm or 0.11811 inch). A quality dial caliper is needed, and i made my spacers to .13 inch to .15 inch. That's close enough to the 0.1094485" average, and the extra thickness gives you some "adjusting" room if needed. (i needed it!) It's best to work only one side when flat sanding, as it's easier to keep the sides parallel when one side is known flat. My setup was complicated more i believe because i used cogs from 2 different manufactures, and a little fine tuning on a few spaces was needed later. Some of that could be avoided using just one maker's cogsets. Check often when sanding, (i used 220 grit on the hard plactic/nylon? spacers), and be prepared for sore fingers. I used several band-aids on my fingertips to help cushion the sharp edges, but i'm still sore. If one part of the sanded spacer is measuring more than a few thousands thicker than the rest of that spacer, you can true it up by only sanding that part and keep the thinner part OFF the sandpaper for a few strokes. Note: You will need to use a NINE SPEED chain, as your 8 speed spacers will be made thinner, making an 8 speed chain unuseable in the more restricted space between cogs. The actual cogs can be either 9 speed or 8 speed, as they are generally within .02mm difference as listed on Sheldon Brown's site. I used what i had on hand,...9 speed cassettes and some old 6 speed spacers. Save yourself some grief and a lot less sanding and sore fingers,....and use an 8 speed cassette(s). The 8 speed spacers are much thinner than the 6 speed ones i had on hand. Best to find one with individual cogs and no spiders, or you'll have to break apart cogs from different sets to get the range you want. (as long as it's 12-26T inclusive). Anyway, after several hours of work (i ended up making TWO sets of spacers, as the 1st ones were a bit too thin :-( One other thing, i was using a new derailluer cable, and the initial stretching was creating it's own problems at times. After a day it's much better now, and holds the settings. Best to get set up using a well used but solid cable! Anyway, i am thrilled to finally be able to use this great looking (and now functioning) derailluer! I went on a 9-10 mile ride today to a LBS, and bought a few more slightly used cassettes...... ......after all, i still have another Dura Ace RD-7402 collecting dust! :-)
Hello, I plan to put this 7402 derailleur on my Bianchi, which has Shimano 1050 groupset. Do you have any idea how this dereailleur performs with the Shimano 1051 shifter (7sp)? I notice that people talking about incompatible issue of old Dura Ace derailleur with modern shifter, but would there be any issue if using with 1051 shifter (more or less in the same period?!) Thank you
This derailleur can also be set up for 9-speed! You'll of course need a 9-speed cassette and chain. Then you need to follow the alternative cable routing described by Sheldon Brown: https://www.sheldonbrown.com/drivetrain-mixing.shtml Works flawlessly! Markus
Building up old bike with 8 speed a RD-7402 and sti levers. I'm contemplating my options to increase size of cassette. Would love to hear thoughts on these or other options I should consider. I'm looking to use a 12x28 or 13x28 cassette. 1) has anyone just used a 12-28 cassette and it worked. 2) use a wolf tooth road link to fit 12-28 3) take cage off an 8 speed xtr rd (short or medium) and install on 7402 to increase cassette size
